|
|
| |
NEW ITEM A group of 4 Shipwright's Caulking Irons by various makers. 5 1/2 to 8 5/8 inches long. Good++
Stock/Part Number: FW12257
|
|
|
|
|
| |
An Unused Twin Iron Nosing Plane by Sargent & Co. No 633. Fine $54.00
Stock/Part Number: *
|
|
|
|
|
| |
A Pair of little used Table Joint Planes by C. R. Wells, who was a planemaker in New Haven, NY (1828 - 1856) Great condition for the collector or user. Fine
Stock/Part Number: FW12242
|
|
|
|
|
| |
NEW ITEM A Fly Fisherman's Rotating Brass Line Dryer. Brass wheel, and brass fittings on the handle. The winder has a bone handle. Made by R. Turner, Edinburgh.
Stock/Part Number: FW9762
|
|
|
|
|
| |
NEW ITEM Twin iron Complex Molding Plane by Gleave. Cuts a Grecian Ogee profile. Irons are good for use. Good ++
Stock/Part Number: FW10048
|
|
|
|
|
| |
NEW ITEM Stanley No 5 Jack Plane. 14 inches long with 2 inch cutter. Used for general smoothing work but long enough to do some jointing. Approximately 95% original finish remains on this plane. Good++ $135.00
Stock/Part Number: FW12269
|
|
|
|
|
| |
NEW ITEM Twin iron Complex Molding Plane by John Miller, Newcastle. Great for use with good irons. Good ++
Stock/Part Number: FW10768
|
|
|
|
|
| |
NEW ITEM A super Handled Compass Rabbit Plane by C. Nurse, with a boxwood adjustable front to vary the radius. i 1/2 inch cutter 9 1/2 inches long. Good++
Stock/Part Number: FW12265
|
|
|
|
|
| |
A Keen Kutter Corner Chisel, 3/4 inch. Good++
Stock/Part Number: FW12193
|
|
|
|
|
| |
NEW ITEM Stanley No 36 Carpenter's Caliper Rule with the sweetheart emblem. Original finish. Good++ $36.00
Stock/Part Number: FW12267
|
|
|
|
|
| |
NEW ITEM Table Joint Plane by Christopher Gabriel. 1770 to 1822. Another excellent early plane by Christopher Gabriel in Good++ condition. $75.00
Stock/Part Number: FWASH2
|
|
|
|
|
| |
NEW ITEM A Stanley No 3 Smoothing Plane, Type 13 - 1925 to 28. This is a great "user" tool. The bottom has been re-ground and there is some staining on the rear of the sole. Part of the original Stanley logo still remains on the tote, however, there is a small chip on the top of the tote as can be seen in the picture. Good+ $98.00
Stock/Part Number: FW11259
|
|
|
|
|
| |
A Set of 18 Hollow & Rounds by Rowell & Gibson, Albany, NY. Great patina all planes in excellent working order. Good++
Stock/Part Number: FW12211
|
|
|
|
|
| |
3/16 inch Beading Plane, fully boxed by C. W. Holden.
Stock/Part Number: FW12251
|
|
|
|
|
| |
NEW ITEM A steel Bullnose Rabbet Plane 3 1/2 inches long, rosewood wedge. 1 inch Howarth iron. Good +
Stock/Part Number: FW12274
|
|
|
|
|
| |
NEW ITEM A Sugar Axe in fruitwood and brass. This unusual whimsical piece of Folk Art is in the female form. Used for chopping sugar from a large block. C1870. 13 inches long Good++
Stock/Part Number: FW12266
|
|
|
|
|
| |
NEW ITEM A Leatherworkers Cutting Tool by Osbourne, NJ. A pretty looking tools as well as extremely functional. This tool has a nice brass ferrule and rosewood handle. Good++ $68.00
Stock/Part Number: FW12259
|
|
|
|
|
| |
A Rosewood Shave with brass front. 2 inch edge. Good+
Stock/Part Number: FW12215
|
|
|
|
|
| |
NEW ITEM Stanley No 7 Jointer Plane, Type 11 . Used for jointing longer planks etc. Sweethart Logo on iron, Stanley Logo on plane handle. Most original finish remains Good++
Stock/Part Number: FW12264
|
|
|
|
|
| |
A European Brace with brass fitting and 1 spoon bit. 10 inch sweep. Marked 3/21/1924, name illegible. Good++
Stock/Part Number: FW12206
|
|
|
|
|
| |
A Woods Patent Hollow Auger with straight 1/2 "dia shank. In excellent user or collector condition. Good++
Stock/Part Number: FW12220
|
|
|
|
|
| |
A Rosewood Spoke Shave with brass wear plate and adjusting nuts. 2 1/2 inch cutting edge. Good++
Stock/Part Number: FW12214
|
|
|
|
|
| |
NEW ITEM Stanley No 5 1/4 Junior Jack Plane. Type 15. 1931 - 32. This is the scaled down, lighter, smaller frame version of the No 5 Jack Plane. It's good for jointing and trimming. Used for manual jobs in furniture making favoured for it's light weight. There is a small flake in the top of the tote. Good ++
Stock/Part Number: FW10654
|
|
|
|
|
| |
A Brass Back saw by A. Rosling of Sheffield, England. This unusually long brass back has a 16 inch saw with 17 tpi. (more on this saw can be found at "www.backsaw.nt/forum/index.php?threads/a-rosling.20/ ) Perfectly usable, the saw has one early replaced screw. Good
Stock/Part Number: FW12244
|
|
|
|
|
| |
A 1/4 Inch Bead Plane by Carter, Syracuse, NY.
Stock/Part Number: FW12250
|
|
|
|
|
| |
NEW ITEM A Floor Saw by Atkins marked No 10. (10 tpi) These unusual looking saws are extremely effective in cutting through floor boards.
Stock/Part Number: FW12272
|
|
|
|
|
| |
A Woods Patent Hollow Auger with square shank. Great condition for using or collecting. Has copy of the Patent papers which are extremely interesting. Good++
Stock/Part Number: FW12221
|
|
|
|
|
| |
NEW ITEM A Planemaker's Float, 10 inches long. Good++
Stock/Part Number: FW12230
|
|
|
|
|
| |
NEW ITEM A Machinist's Brass Hammer by Millers Falls Co. USA. Good++
Stock/Part Number: FW12252
|
|
|
|
|
| |
NEW ITEM A Stanley No 4 Smoothing Plane, Type 19, 1930 to 1942. A great plane for the user with an excellent iron. Rosewood handle and knob. Original japanning worn which doesn't detract from the use of the plane. Good+ $95.00
Stock/Part Number: FW12230
|
|
|
|
|
| |
A Keen Kutter Corner Chisel, 1 inch. Good++
Stock/Part Number: FW12194
|
|
|
|
|
| |
NEW ITEM Stanley No 12, 2 inch metal Nickel Plated Try Square. Unusually small size, marked to measure 2 inches in 1/8th inch increments. The Stanley logo is cast into the frame, early 1900's.
Stock/Part Number: FW12273
|
|
|
|
|
| |
NEW ITEM A Shipwright's Lignum Vitae banded Caulking Mallet with 2 irons. Excellent mallet, no splits, with two caulking irons. Good++
Stock/Part Number: FW12262
|
|
|
|
|
| |
NEW ITEM 1/2 inch Round by Christopher Gabriel, 1770 to 1822. A fine example of an 18th Century plane. Christopher Gabriel was a plane maker in London. His earliest planes have flat chamfers on the shoulders, as this example does, but most are found with oval chamfers as found in the famous Seaton Chest. Christopher Gabriel died in 1809, his business which was quite diverse, was continued by his sons. Good++ $75.00
Stock/Part Number: FWASH1
|
|
|
|
|
| |
NEW ITEM An all Brass Bull Nose Plane, 1 1/16 inch cutter made by Marples. Over all length 3 7/8 inch. AWH initials on side (previous owner). Good+
Stock/Part Number: FW8716
|
|
|
|
|
| |
NEW ITEM 4 Shipwright's Caulking irons.
Stock/Part Number: FW12263
|
|
|
|
|
| |
NEW ITEM Twin iron Complex Molding Plane by Mathieson. Irons are fine and good for using. Good ++
Stock/Part Number: FW10664
|
|
|
|
|
| |
NEW ITEM A 10 inch Mahogany Level with solid brass top and bottom plates. A great coffee table show piece that is also very useful when hanging pictures and wall decor. Good++ $ 60.00
Stock/Part Number: FW9830
|
|
|
|
|
| |
A Rosewood Tool Handle by Springfield Tool & Level Co. Seven tools that store inside the handle. 7 1/2 inches long. (Similar to the Millers Falls No 4). Good++
Stock/Part Number: FW12202
|
|
|
|
|
| |
An Unusual Precision Pitch Grade Level (inclinometer) by Engineering Devices Inc. Sunbury, PA. In the original leather case. Marked inside, Distributed by Joseph G. Pollard Co. Inc. New Hyde Park, NY. Good++
Stock/Part Number: FW12208
|
|
|
|
|
| |
A Quirk Ovolo and Bead Complex Molding Plane by Varvill, York. Good++ $68.00
Stock/Part Number: *
|
|
|
|
|
| |
NEW ITEM A Stair Saw made from Walnut with nicely carved handle. Good++
Stock/Part Number: FW12243
|
|
|
|
|
| |
NEW ITEM A Steel Back saw by Turtle, Croyden. 14 inches long, 10 tpi. This saw has been resharpened. Good++
Stock/Part Number: FW10714
|
|
|
|
|
| |
NEW ITEM Sheffield Plated Brace. Beech wood with push button chuck. Nice brass neck with a Rosewood head. Good ++
Stock/Part Number: FW8429
|
|
|
|
|
| |
NEW ITEM Millers Falls No 2, 4 way spoke shave. One of the less common spoke shaves with radius attachment. Rosewood handles. Good++ $ 95.00
Stock/Part Number: FW12270
|
|
|
|
|
| |
A Handled Screw Stem Plow Plane with brass fittings. Unmarked, probably user made from birch wood. Unusually long, 13 3/4 inches over all, with a 9 inch brass skate. Good++
Stock/Part Number: FW12258
|
|
|
|
|
| |
NEW ITEM A 10 1/2 inch Ebony Level with solid brass top and bottom plates. Made by James Howarth of Sheffield, England. Good++ $78.00
Stock/Part Number: FW10162
|
|
|
|
|
| |
A Pair of Ornamental Victorian Ladies Boots, made in brass, 4 1/2 inches high. These mantle ornaments were made by work shop apprentices to show off their skill of working with brass. Good+
Stock/Part Number: FW11432
|
|
|
|
|
| |
A Solid Brass Pedestal Kettle Trivet with fancy pierced brass top. 12 inches tall. This trivet is a very decorative, the base is brass over steel, which gives the trivet stability. C 1880. A fine addition to the hearth. Good++
Stock/Part Number: FW11119
|
|
|
|
|
| |
A Round Copper Hot Water Bottle with brass screw top. Often covered with a blanket and used for traveling in the late 1800s into early 1900s. This one has a few minor "character" dents. Often used these days as a decorative hearth piece. Good+
Stock/Part Number: FW11121
|
|
|
|
|
| |
This book is Out of Print "Patented Transitional & Metallic Planes in America 1827-1927" by Roger K. Smith. Only 1 Copy Available This 1981 First Edition covers developments from the very first patented metallic planes through the beginning of the 20th Century. The chapters cover Stanley, Leonard Bailey, Stanley's competitors, patented combination planes and more. Includes type studies of Stanley planes, patent drawings and illustrations from early catalogs. Invaluable information for the antique tool collector and a superb reference for museums. Given as a gift, there is a small personal inscription inside the front cover. Excellent condition. Hard Bound. 336 pages. 11" x 9"
Stock/Part Number: Pat. Trans & Metal by R K Smith
|
|
|
|
|
| |
A Pair of Brass and Steel Trammels on a 36 inch beam. The trammels are 6 inches long with steel points and knurled top screws. One trammel has an extra fine adjustment screw, which is knurled to match the top screws. Good++
Stock/Part Number: FW10141
|
|
|
|
|
| |
A 10 inch Mahogany Sighting Level. Fully brass bound with a fancy top. Good cross hairs in the sight. A handsome gift! Good++
Stock/Part Number: FW9437
|
|
|
|
|
| |
A Very nice Panel Gauge. Padouk wood with boxwood head and adjusting screw. Good+
Stock/Part Number: FW10597
|
|
|
|
|
| |
A 7/8 inch Bead Plane by Buck. Good+
Stock/Part Number: FW11389
|
|
|
|
|
| |
A 3/4 inch Ovolo Plane by Tyzac & Son. Good++
Stock/Part Number: FW11393
|
|
|
|
|
| |
A Lying Ogee with Bevel, Complex Molding Plane by Cox & Luckman, Birmingham. Good++
Stock/Part Number: FW11390
|
|
|
|
|
| |
A Quirk Ogee with Bead Molding Plane, marked No 4 by Joseph Gleave, Bolton. Good++
Stock/Part Number: FW11361
|
|
|
|
|
| |
A Complex Molding Plane by Watsons, Leeds, early 1800s. A Flute, Quirk & Fillet profile. Good
Stock/Part Number: FW11428
|
|
|
|
|
| |
A Boxed Quirk & Fillet by King and Prague, Hull. marked No 6 on the heel. Good+
Stock/Part Number: FW11365
|
|
|
|
|
| |
An Ogee and Bevel by King & Peach, Hull, 1848 to 1864. Good++
Stock/Part Number: FW11449
|
|
|
|
|
| |
A 5/8 inch Cove and Ogee by Wm Moss, 1812 to 1844. Good+
Stock/Part Number: FW11450
|
|
|
|
|
| |
A 6/8 inch Cove & Bevel by O'Kines, C1825. Good+
Stock/Part Number: FW11452
|
|
|
|
|
| |
A Steel and Brass Plumb Bob. Measures 2 3/4 inches long. Good++
Stock/Part Number: FW11425
|
|
|
|
|
| |
An unusual shaped Brass Plumb Bob with steel tip. Good+
Stock/Part Number: FW7004
|
|
|
|
|
| |
A small Oval Copper Kettle with dovetailed seams C1850. Swan neck spout, water tight (pours like a dream) some minor dings. Oval body measures 5 1/2 inches by 4 1/2 inches.Good+
Stock/Part Number: FW11430
|
|
|
|
 "Shipwright's Caulking Irons")
 "Unused Twin Iron Nosing Plane by Sargent & Co. No 633.")
 "Table Joint Planes by C. R. Wells")
 "Fly Fisherman's Line Dryer")
 "Complex Molding Plane by Gleave")
 "Stanley No 5 Jack Plane")
 "Twin iron Complex Molding Plane by Miller")
 "Handled Compass Rabbit Plane by C. Nurse")
 "Keen Kutter Corner Chisel, 1 inch")
 "Stanley No 36 Carpenter's Caliper Rule")
 "Table Joint Plane by Christopher Gabriel")
 "Stanley No 3 Smoothing Plane, Type 13")
 "Set of 18 Hollow & Rounds by Rowell & Gibson, Albany, NY")
 "3/16 inch Beading Plane by Holden")
 "Bullnose Rabbet Plane")
 "Sugar Axe")
 "Leatherworkers Cutting Tool by Osbourne")
 "Rosewood Shave with brass front")
 "Stanley No 7 Jointer Plane")
 "European Brace with brass fitting")
 "Woods Patent Hollow Auger with straight 1/2 \"dia shank")
 "Rosewood Spoke Shave with brass wear plate")
 "Stanley No 5 1/4 Junior Jack Plane.")
 "Brass Back saw by A. Rosling of Sheffield, England.")
 "1/4 Inch Bead Plane by Carter")
 "Floor Saw by Atkins")
 "Woods Patent Hollow Auger with square shank")
 "Planemaker's Float")
 "Millers Falls Machinist's Brass Hammer")
 "Stanley No 4 Smoothing Plane, Type 19, 1930 to 1942")
 "Keen Kutter Corner Chisel, 1 inch.")
 "Stanley No 12 Try Square 2 inch")
 "Caulking Mallet with 2 irons")
 "1/2 inch Round by Christopher Gabriel")
 "Brass Bull Nose Plane with Marples Iron")
 "4 Shipwright's Caulking Irons")
 "Twin Iron Complex Molding Plane by Mathieson")
 "10 inch Mahogany Level")
 "Rosewood Tool Handle by Springfield Tool & Level Co")
 "Precision Pitch Grade Level")
 "Quirk Ovolo and Bead Complex Molding Plane by Varvill")
 "Walnut Stair Saw")
 "Steel Back Saw 14 inch by Turtle")
 "Sheffield Plated Brace")
 "Millers Falls No 2, 4 way spoke shave")
 "Handled Screw Stem Plow Plane")
 "10 1/2 inch Ebony Level")
 "Pair of Ornamental Victorian Ladies Boots")
 "Solid Brass Pedestal Kettle Trivet")
 "Round Copper Hot Water Bottle")
 "\"Patented Transitional & Metallic Planes in America 1827-1927\" by Roger K. Smith")
 "Pair of Brass and Steel Trammels on a 36 inch beam")
 "10 inch Mahogany Sighting Level.")
 "Panel Gauge. Padouk wood with boxwood head and adjusting screw")
 "7/8 inch Bead Plane by Buck")
 "3/4 inch Ovolo Plane by Tyzac & Son")
 "Lying Ogee with Bevel, Complex Molding Plane by Cox & Luckman")
 "Quirk Ogee with Bead Molding Plane, marked No 4 by Joseph Gleave")
 "Complex Molding Plane by Watsons, Leeds")
 "Boxed Quirk & Fillet by King and Prague, Hull")
 "Ogee and Bevel by King & Peach")
 "5/8 inch Cove and Ogee by Wm Moss")
 "Cove & Bevel by O'Kines")
 "Steel and Brass Plumb Bob")
 "Brass Plumb Bob")
 "Oval Copper Kettle")
